( DOWNLOAD PDF )

INSTRUCTIONS FOR APPLYING MICROCEMENT IN WALLS 

*The surface must be clean, free of moisture and compact; if the surface don´t have these characteristics you must solve the problem.

1) Adhesion promoter ( 1 component) , Apply one layer with a paint roller along with the fiberglass mesh. Let dry for 30 minutes before apply the microcement base

2) Microcement Base -  1st layer, in a clean bucket add the resin component B already colored,  and gradually add the microcement, beat for 3/5 minutes until reaching a honey-like consistency, then spread the material with a Steel trowel on the surface .  Let dry for 3/5 hours, then with sandpaper grit 40, pass through the surface, eliminating the imperfections.

3) Microcement Base - 2nd layer, install the second coat of the microcement Base,in the same way. Let dry for 3/5 hours, then sand with sandpaper grit 40.

4) Microcement Fino 1st layer, mix in the same way as the base Microcement, and then apply a thin layer with a steel or plastic trowel. Let dry for 3/5 hours, then sanding with sandpaper, grit 150 the whole surface.

 5) Microcement Fino 2nd layer, repeat all the steps of the previous phase to apply the last layer of Micro Beton,  Let dry for 24 hours, then sanding with sandpaper, grit 150 the whole surface, after that , clean with a damp cloth until the surface is completely free of dust.

6) Primer Sealer , apply 2 layers with a paint roller, Let dry the first coat for 15/30 min, then apply the second coat. After that, let dry about 3 hours.

7) Polyurethane sealer 2 components, Apply with roller the polyurethane varnish sealer of two components ( Barniz poliuretano alifatico al agua + hardener ) ratio 1: 10 (10 % ) , let dry well  3 or 4 hours and apply the  second final layer, after the 2 layers, let dry one day.

Total hardening of the Polyurethane isafter 7 days

USEFUL DATA

( DOWNLOAD PDF ) 

INSTRUCTIONS FOR APPLYING MICROCEMENT FOR FLOORS

*The surface must be clean, free of moisture and compact; if the surface don´t have these characteristics you must solve the problem.

1) Epoxy Adhesion promoter, mix the two-component epoxy (imprimacion epoxi al agua), add 20% water, and apply just one coat with the paint roller along with the fiberglass mesh. The drying time is 12 Hours.

2) Microcement Base -  1st layer, in a clean bucket add the resin component B already colored,  and gradually add the microcement, beat for 3/5 minutes until reaching a honey-like consistency, then spread the material with a Steel trowel on the surface .  Let dry for 3/5 hours, then with sandpaper grit 40, pass through the surface, eliminating the imperfections.

3) Microcement base - 2nd layer, install the second coat of the microcement Base,in the same way. Let dry for 3/5 hours, then sand with sandpaper grit 40.

4) Micro Beton 1st layer, mix in the same way as the base Microcement, and then apply a thin layer with a steel or plastic trowel. Let dry for 3/5 hours, then sanding with sandpaper, grit 150 the whole surface.

 5) Micro Beton 2nd layer, repeat all the steps of the previous phase to apply the last layer of Micro Beton,  Let dry for 24 hours, then sanding with sandpaper, grit 150 the whole surface, after that , clean with a damp cloth until the surface is completely free of dust.

6) Primer Sealer , apply 2 layers with a paint roller, Let dry the first coat for 15/30 min, then apply the second coat. After that, let dry about 3 hours.

7) Polyurethane sealer 2 components, Apply with roller the polyurethane varnish sealer of two components ( omacril + endurecedor Na ) ratio 2:1 ,  plus the thinner (disolvente poliuretanos )  5 to 15 % of the mixture that comes with the kit, let dry well  3 or 4 hours and apply the  second final layer.

Total hardening of the Polyurethane isafter 7 days

USEFUL DATA